公司新聞
冷再生機機械保養注意事項？
來源：http://hk-pinyan.cn/ 日期：2020-09-11
天氣清冷之前，機械該如何進行保養呢？
Before the cold weather, how to maintain the machinery?
一、清洗外表
1、 Clean the exterior
冷再生機在施工過程中會有大量的灰塵落到再生機的表面，包括施工中沾污的油跡等污染物，影響外觀事小，更為嚴重的是成為腐蝕的誘發因素。
During the construction of cold regenerator, a large amount of dust will fall on the surface of the regenerator, including oil stains and other pollutants in the construction, which has little influence on the appearance, and more seriously, it becomes the inducing factor of corrosion.
1.清洗工程機械的柴油機、底盤、工作裝置的外表,除垢、除油保持再生機的外觀整潔。
1. Clean the appearance of diesel engine, chassis and working device of construction machinery, remove dirt and oil, and keep the appearance of regenerator clean.
2.清洗時嚴禁用高壓、高溫的水槍來沖洗防水要求較高的部位（特別是電器部分），以免造成電器部分的損壞。
2. It is forbidden to use high-pressure and high-temperature water gun to wash the parts with high waterproof requirements (especially the electrical parts), so as to avoid damage to the electrical parts.
清洗外表，是工程機械冬季保養要點之一。
Cleaning appearance is one of the key points of winter maintenance of construction machinery.
二、 保養轉子及其罩殼和滑靴
2、 Maintain the rotor and its casing and slippers
1.檢查轉子是否有水泥結垢等，及時清理灰塵，對需要割除、焊接的刀具及時更換；
1. Check whether there is cement scaling on the rotor, clean up the dust in time, and replace the cutting tools that need to be cut and welded in time;
2.清理轉子罩殼上的灰塵，并在施工結束收車時將轉子罩殼墊起地面5-10公分，防止雨雪的浸蝕；
2. Clean the dust on the rotor housing, and pad the rotor housing 5-10 cm above the ground to prevent the erosion of rain and snow at the end of construction;
3.檢查滑靴，對已經磨損的滑靴部分進行補焊，螺紋處應涂抹黃油防銹。
3. Check the slipper, repair the worn part of the slipper, and apply grease on the thread to prevent rust.
三、減速機齒輪油的更換方式
3、 Replacement method of gear oil for reducer
準備事項：
Preparation:
1、場地:要求無塵硬化路面，面積應在200平方米左右，盡量是庫房，但要有足夠25噸的吊車的工作高度和半徑。
1. Site: it is required to harden the road surface without dust. The area should be about 200 square meters. It should be a warehouse as far as possible, but there should be enough working height and radius of 25 tons of crane.
2、設施：25噸吊車一臺（20噸也可以）。
2. Facilities: a 25 ton crane (20 tons is OK).
3、配件：進口美孚齒輪油9升、衛生紙10卷、塑料帶20個、廢油桶2個、緊固膠262/340一支、密封膠587一支、黃油一袋，細線繩20米、 12 *45的帶母螺栓30套、4*30開口銷10個。
3. Accessories: imported Mobil gear oil 9L, 10 rolls of toilet paper, 20 plastic belts, 2 waste oil drums, a 262 / 340 fastening glue, 587 sealant, a bag of butter, 20 meters of string, 30 sets of 12 * 45 female bolts and 10 4 * 30 split pins.
4、工具：10、16、18、19、21、22、24、30套筒和扳手至少一套、快速扳手及長、短接桿各一、加力桿一根、30的輪胎扳手、10毫米的內六角扳手、55的活口扳手兩把、小號活口扳手一把、小號的老虎鉗一把、手鉗一把、一字螺絲刀一把、大小錘頭各一、撬棍兩根，配備氣動扳手和氣泵，能提高工作效率。
4. Tools: at least one set of 10, 16, 18, 19, 21, 22, 24, 30 sockets and spanners, one quick wrench and one long and short extension rod, one afterburner, 30 tire wrench, 10 mm hexagon wrench, two 55 adjustable spanners, one small loose end wrench, one small vice, one hand vice, one slotted screwdriver, one hammer head and two crowbars Pneumatic wrench and air pump can improve work efficiency.
?。p速機油位及減速機油的檢查：先切斷電源，等待減速機冷卻后打開放油螺塞，檢查油是否充滿，避免漏油， 取油樣，檢查油色澤及粘度指數，如果油明顯渾濁，建議盡快更換。新減速機使用后（500-1000）小時更換新油（將內部污油沖干凈），其后每使用1500小時需要更換油一次，但是在使用過程中，仍需要檢查油的質量，若油有老化、變質情況要隨時更換。）
(inspection of reducer oil level and reducer oil: cut off the power supply, wait for the reducer to cool down, open the oil drain plug, check whether the oil is full to avoid oil leakage, take oil sample, check oil color and viscosity index, if the oil is obviously turbid, it is recommended to replace it as soon as possible. After the new reducer is used for (500-1000) hours, the new oil shall be replaced (the internal dirty oil shall be flushed out), and then the oil shall be replaced every 1500 hours. However, the quality of the oil still needs to be checked during the use, and the oil shall be replaced at any time in case of aging and deterioration.)
以上是關于冷再生機保養事項的相關內容介紹，希望對大家有所幫助，如您想要了解更多內容歡迎點擊冷再生機出租http://hk-pinyan.cn官網。
The above is about the cold regenerator maintenance related content introduction, I hope to help you, if you want to know more, welcome to click the cold regenerator rental http://hk-pinyan.cn Official website.
公司地址：濟南市槐蔭區經一路273號群盛華城2號樓1-404
公司名稱：山東途暢路橋工程有限公司 
備案號：