小说网,欢乐颂第二季

行業資訊

水泥撒布車傳感器的使用方法！

來源：http://hk-pinyan.cn/ 日期：2020-09-08

　　傳感器的使用

　　Use of sensors

　　傳感器位于絞龍、計量器及排雜電機位置，主要起到轉速信號傳感的作用。

　　The sensor is located in the position of auger, metering device and trash removal motor, which mainly plays the role of speed signal sensing.

　　電感式傳感器自帶調節絲紋，可調節傳感距離；傳感器后尾部正常工作時為黃色傳感燈閃爍，如正好處于傳感齒牙位置時為黃色傳感燈常亮，通常離傳感齒牙3mm左右。

　　The inductive sensor has its own adjustable silk grain, which can adjust the sensing distance; when the rear tail of the sensor works normally, the Yellow sensor light flashes, if it is just in the position of the sensing tooth, the Yellow sensor light is always on, usually about 3 mm away from the sensing tooth.

　　1.電感式傳感器需要檢查以下幾點：

　　1. Inductive sensor needs to check the following points:

　?。?）、傳感距離是否過遠

　　(1) Is the sensing distance too far
水泥撒布車出租

　?。?）、傳感位置是否偏離齒輪牙盤

　　(2) Whether the sensing position deviates from the gear tooth disc

　?。?）、用物品在傳感器前端位置移動測試，查看傳感燈是否閃爍，如常亮則有可能需要更換傳感器

　　(3) Use the object to move the front end of the sensor to check whether the sensor lamp flickers. If it is normally on, the sensor may need to be replaced

　　2.如確定傳感器已損壞，臨時可運用參數設置里的調試功能臨時施工，同時聯系我司及時配發配件，具體步驟如下：

　　2. If it is confirmed that the sensor has been damaged, the debugging function in parameter setting can be used for temporary construction, and at the same time, contact our company to distribute accessories in time. The specific steps are as follows:

　　（1）、按照以下順序操作：

　　(1) And operate in the following order:

　　狀態→診斷→輸出，調整到輸出檢測頁面

　　Status → diagnosis → output, adjust to output detection page

　?。?）、旋轉右上角旋轉調鈕選擇需要調試的傳感器，選擇調試功能后設備能暫時正常運轉。

　　(2) Rotate the upper right corner knob to select the sensor to be debugged. After the debugging function is selected, the equipment can operate normally temporarily.

　　3.選擇調試功能后使用需要注意：

　　3. After the debugging function is selected, attention should be paid to:

　　調試后轉速會和原轉速有所不同，有可能會高于或低于原轉速，同時對撒布量的準確控制會產生一定的影響。

　　After debugging, the speed will be different from the original speed, which may be higher or lower than the original speed, and it will have a certain impact on the accurate control of spreading amount.

　　以上是關于水泥粉料撒布車傳感器的使用方法，希望對大家有所幫助，如您還有其他問題歡迎咨詢我們的網站。

　　The above is about the use of the sensor of cement powder spreader, hope to help you, if you have other questions, please consult our website.

上一條：大部分企業選擇冷再生機的理由?

下一條：冷再生技術質量檢查程序是什么?